GY6 125 -150cc, 4-Stroke, (152QMI 152QMJ 157QMI 157QMJ)

The 152QMI (GY6-125) & 157QMJ (GY6-150) (QMI152 QMJ157) is a horizontal, single-cylinder, four stroke, forced air cooled engine. This has a displacement of 149.6cc (157QMJ) has a bore size of 57.4mm and a stroke of 57.8mm.  This type-A Honda clone engine has a automatic CTV transmission. This engine is used on many scooters, dirt bikes, quads, ATVs, go karts, and buggies.

Here are just a few of the many brands and models this very common engine is found on:
Avanti Beta 150, Avanti Epsilon 150cc, Baja, Bemine 150 Touring, Diamo 150, Diamo, Velux 150, Genuine Blur 150, Genuine G-Max, Howhit 150, JMstar, Jonway,
Jonway YY150T-2, Kinroad XT150T-8, Kymco, Lifan 125/150, Lifan L150T-7, Loncin 150, Longbo 150, Longbo LB150T-12, Mod Cycle 150, NST, Peace Sports 150, Primo "Strada" Streaker 150, Primo Terminator 150cc, Racer 150, RAD-10 150cc, Retro 150, Roketa, Roketa Fiji MC-04, Roketa Tahiti MC-03, Schwinn, Spigaly 150, Strada 150CE, Strada Chrome Edition RX150, Strada RX150TE, Strada RX200HP, Sunl, SYM, Tank, Tank 150cc (various models), Tank Racer 150, TNG, Tomos, Velux 150, Vento Phantom GT5 150cc, Vento Phantom R4I 150cc, Verucci Permier 150GTX SE, Verucci Viper 150GTX, VIP, Wangye 150, Wussi 150, Znen and many others...

(Click on the parts for additional pictures)

Sort By:
743-20-30 Belt Gates Powerlink GY6 150 157QMJ Short Case Scooter Moped ATV 200-1001-1009
$14.99 $14.99 Add to Cart

This is a High Quality Gates Powerlink Belt for the GY6 125/150cc 152QMI 152QMJ 157QMI 157QMJ "short case" engine. This belt fits Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others. Save time and money, go for quality.  Note: Scooters with a 10" rear wheel usually have a short case engine.  Here are a few go karts and buggies that use this belt: ACE Sports Maxxam 150 2R (part number: 513-1046), American Sportworks Carbide / Quantum 7150 (part number: 14363), Carter Brothers Talon GSR 150 R 2 (part number: 513-1046), Carter Brothers Talon GSX 150 R 2 (part number: 513-1046), Gio Bikes 150 GT, Hammerhead 150 SS (part number: M150-1033000), Hammerhead 150 GT (part number: M150-1033000), Hammerhead GTS 150 (part number: M150-1033000).

743-20-30 Belt GY6 150 157QMJ Short Case Scooter Moped ATV 200-1001-1008
$14.99 $14.99 Add to Cart

This is a standard replacement belt for the GY6 125/150cc 152QMI 152QMJ 157QMI 157QMJ "short case" engine. . This belt is found on the is used on the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others. Note: Scooters with a 10" rear wheel usually have a short case engine.  Here are a few go karts and buggies that use this belt: ACE Sports Maxxam 150 2R (part number: 513-1046), American Sportworks Carbide / Quantum 7150 (part number: 14363), Carter Brothers Talon GSR 150 R 2 (part number: 513-1046), Carter Brothers Talon GSX 150 R 2 (part number: 513-1046), Gio Bikes 150 GT, Hammerhead 150 SS (part number: M150-1033000), Hammerhead 150 GT (part number: M150-1033000), Hammerhead GTS 150 (part number: M150-1033000).

815-20-30 Belt CFmoto CF150 Water Cooled 4 stroke 1P58MJ 157MJ E-Charm E-Jewel QJ CPI 500-1001-1012
$19.99 $19.99 Add to Cart

This is a standard replacement belt for the GY6 125/150cc QJ CPI engine. This belt is used on Andretti, Benelli, CPI Husser, Diamo, QJ, Strada, TNG, United Motors, Vento, Xtreme, Yamati and many others... (Please note our new belts are 815-20-32 which only effects the angle of the teeth. Length is 815mm long.)

815-20-30 Belt Gates PowerLink CFmoto CF150 Water Cooled 4 stroke 1P58MJ 157MJ E-Charm E-Jewel 500-1001-1016
$24.99 $24.99 Add to Cart

Belt, Drive, 815-20-30, Gates PowerLink, found on some GY6-125/150 as well as Andretti, Benelli, CF Moto, CPI Husser, Diamo, QJ, Strada, TNG, United Motors, Vento, Xtreme, Yamati and others.

830-20-30 Belt GY6 150 250 Diamo Retro 172MM Strada Vento Vmoto 200-1001-1034
$14.99 $14.99 Add to Cart

This is the standard drive belt for many ATVs and scooters with the GY6 150 and 250cc engines, Diamo Retro 150cc scooters, and the Linhai Yamaha VOG 260cc and 300cc scooter and ATV engines.

835-20-30 Belt Gates Powerlink GY6 150 157QMJ Long Case Scooter Moped ATV 200-1001-1035
$24.99 $24.99 Add to Cart

This is a high quality Gates PowerLink Drive Belt 835-20-30, for the Long-Case (10 bolt) GY6 150cc 157QMI 157QMJ engine.  Note: Scooters with a long case usually have a 12" - 16" rear wheel.   Save time and money, go for quality.  This belt is found on the is used on the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others. Note: Scooters with a 10" rear wheel usually have a short case engine.  Here are a few go karts and buggies that use this belt: ACE Sports Maxxam 150 2R (part number: 513-1046), American Sportworks Carbide / Quantum 7150 (part number: 14363), Carter Brothers Talon GSR 150 R 2 (part number: 513-1046), Carter Brothers Talon GSX 150 R 2 (part number: 513-1046), Gio Bikes 150 GT, Hammerhead 150 SS (part number: M150-1033000), Hammerhead 150 GT (part number: M150-1033000), Hammerhead GTS 150 (part number: M150-1033000).

835-20-30 Belt GY6 150 157QMJ Long Case Scooter Moped ATV 200-1001-1014
$14.99 $14.99 Add to Cart

This is a standard replacement belt for the GY6 125/150cc 152QMI 152QMJ 157QMI 157QMJ "long case" engine. . This belt is found on the is used on the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others. Note: Scooters with a long case usually have a 12" - 16" rear wheel.

842-20-30 Belt Gates Powerlink GY6 150 157QMJ Long Case Scooter Moped ATV 200-1001-1019
$25.99 $25.99 Add to Cart
5 out of 5 Stars!

This is a High Quality Gates Powerlink Belt for the GY6 125/150cc 152QMI 152QMJ 157QMI 157QMJ "long case" engine. This belt fits Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others. Note: Scooters with a long case usually have a 12" - 16" rear wheel. Save time and money, go for quality every time.

842-20-30 Belt GY6 150 157QMJ Long Case Scooter Moped ATV 200-1001-1018
$14.99 $14.99 Add to Cart

This is a standard replacement belt for the GY6 125/150cc 152QMI 152QMJ 157QMI 157QMJ "long case" engine. This belt is found on the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.  Note: Scooters with a long case usually have a 12" - 16" rear wheel.

Air Box GY6 150 157QMJ Scooter Moped ATV 200-1015-1010
$30.29 $30.29 Add to Cart

This is a Complete OEM Replacement Air Box with a brand new Pre-filter and Air Filter already installed, for the 4 stroke, GY6-150, 157QMJ engine scooter, ATV, quad and buggie engine.  This fits Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

Air Filter 42mm 1 5/8" 30 degree High Flow Pod Dual Layer 201-1015-1002
$12.89 $12.89 Add to Cart

This is a very High Quality Dual Layer 42mm, 30 degree, small profile Performance Air Filter for high air flow that clamps on to your carburetor to ensure a tight clearance fit. This has a quality Urethane Flange and clamp. Unlike some 50’s this does not have a suspension cross member which would interfere with the filter installation. This filter fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50,  Vento, VIP and many others. This will fit just about any scooter, quad, moped, buggy, ATV, dirt bike, etc

Air Filter 42mm 1 5/8" 30 Degree Performance Blue Chrome Cone 201-1015-4024
$16.99 $16.99 Add to Cart
4 out of 5 Stars!

This is a very High Quality High Flow (42mm), 30 Degree, Blue/Chrome Cone,  (approx 90mm long), small profile Performance Air Filter for high air flow that clamps on to your carburetor to ensure a tight clearance fit. This has a quality Urethane Flange and clamp. This filter fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50,  Vento, VIP and many others. This will fit just about any scooter, quad, moped, buggy, ATV, dirt bike, etc

Air Filter 42mm 1 5/8" 90 Degree Performance Blue Chrome Cone 201-1015-4021
$16.99 $16.99 Add to Cart

This is a very High Quality High Flow (42mm), 90 Degree, Blue/Chrome Cone,  (approx 90mm long), small profile Performance Air Filter for high air flow that clamps on to your carburetor to ensure a tight clearance fit. This has a quality Urethane Flange and clamp. This filter fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50,  Vento, VIP and many others. This will fit just about any scooter, quad, moped, buggy, ATV, dirt bike, etc

Air Filter 42mm 1 5/8" Straight High Flow Pod Dual Layer 201-1015-1004
$16.99 $16.99 Add to Cart

This is a very High Quality Dual Layer 42mm, Red, Straight, small profile Performance Air Filter for high air flow that clamps on to your carburetor to ensure a tight clearance fit. This has a quality Urethane Flange and clamp. Unlike some 50’s this does not have a suspension cross member which would interfere with the filter installation. This filter fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50,  Vento, VIP and many others. This will fit just about any scooter, quad, moped, buggy, ATV, dirt bike, etc

Air Filter 42mm 1 5/8" Straight High Flow POD Dual Layer 201-1015-1003
$16.99 $16.99 Add to Cart

This is a very High Quality Dual Layer 42mm, Black, Straight, small profile Performance Air Filter for high air flow that clamps on to your carburetor to ensure a tight clearance fit. This has a quality Urethane Flange and clamp. Unlike some 50’s this does not have a suspension cross member which would interfere with the filter installation. This filter fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50,  Vento, VIP and many others. This will fit just about any scooter, quad, moped, buggy, ATV, dirt bike, etc

Air Filter 42mm 1 5/8" Straight Performance Blue Chrome Cone 201-1015-4018
$16.99 $16.99 Add to Cart

This is a very High Quality High Flow (42mm), Straight, Blue/Chrome Cone, Performance Air Filter for high air flow that clamps on to your carburetor to ensure a tight clearance fit. This has a quality Urethane Flange and clamp. This filter fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50,  Vento, VIP and many others. This will fit just about any scooter, quad, moped, buggy, ATV, dirt bike, etc

Air Filter 42mm 1 5/8" Straight Performance Shielded Chrome Cone 400-1015-4012
$12.99 $12.99 Add to Cart

This is a very high quality Air Filter, 42mm, 4-Stroke HP Air Filter, Straight, Shielded Chrome Cone (approx 90mm long) for the 152QMI 152QMJ 157QMI 157QMJ GY6 125cc 150cc and many other engines.

Air Filter GY6 150 157QMJ Scooter Moped ATV 200-1015-4008
$10.69 $10.69 Add to Cart

This is a very High Quality OEM Air Filter for high air flow in the GY6-125cc 150cc 152QMI 152QMJ 157QMI 157QMJ engine. This filter fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50,  Vento, VIP and many others. This will fit just about any scooter, quad, moped, buggy, ATV, dirt bike, etc

Bearing 6002 15mm x 32mm x 9mm Chrome Steel B-1-1000-2002
$8.49 $8.49 Add to Cart

6002 Bearing, Open, Deep Groove Ball Bearing, Chrome Steel, 15mm x 32mm x 9mm, GY6-125/150 crankcase

Bearing 6004Z 6004-2RS 20mm x 42mm x 12mm Sealed Chrome Steel B-1-1000-2007
$4.99 $4.99 Add to Cart

6004Z 6004-2RS, Bearing, double sealed ball bearing, 20mmx42mmx12mm, GY6-125/150 152QMi 152QMJ 157QMI 157QMJ crankcase, GY6-50 139QMB gear box

Bearing 6202 15mm x 35mm x 11mm Chrome Steel 1PE40QMB 157QMJ B-1-1000-2012
$4.99 $4.99 Add to Cart

6202 Bearing, Open, Chrome Steel, Deep Groove Ball Bearing, 15mm x 35mm x 11mm, 1PE40QMB Transmission, GY6-125/150 gear box, TGB, Vento Zip R3i, Vento Triton.

Bearing 6202-2RS 15mm x 35mm x 11mm Sealed Deep Groove B-1-1000-2013
$4.99 $4.99 Add to Cart

6202-2RS, Bearing, Sealed Ball Bearing, Rubber sided,  Deep Groove, 15mm x 35mm x 11mm, Self-lubricating, Equivalents: 202PP, 6202.2RSR, 202SZZ, 6202DDU, 6202LLU and 6202-2RS1

Bearing 6203 17mm x 40mm x 12mm Chrome Steel 1PE40QMB 139QMB 157QMJ B-1-1000-2014
$4.99 $4.99 Add to Cart

6203 Bearing, Open, Deep Groove Radial Ball Bearing, Chrome Steel, 17mm x 40mm x 12mm, 1PE40QMB 50 Rear Transmission, GY6-50 139QMB crankcase, GY6-125/150 157QMJ gear box.

Bearing 6204 20mm x 47mm x 14mm Chrome Steel 1PE40QMB 157QMJ  B-1-1000-2018
$4.99 $4.99 Add to Cart

6204 Bearing,  Open, Deep Groove Ball Bearing, Chrome Steel, 20mm x 47mm x 14mm, 1PE40QMB 50 Crankshaft (2), GY6-125/150 gear box, and other uses

Bearing 6204-Z 20mm x 47mm x 14mm Chrome Steel 157QMJ 1PE40QMB B-1-1000-2021
$4.99 $4.99 Add to Cart

6204-Z, Radial Ball Bearing, Single Side Shield, Deep Groove, Chrome steel, 20mmx47mmx14mm, 157QMJ GY6-125/150, 1PE40QMB 50cc Rear Transmission

Bearing 63/22x2/C3 22mm x 56mm x 15mm Chrome Steel 157QMJ B-1-1000-2030
$4.99 $4.99 Add to Cart

63/22x2/C3 Bearing, Open, Deep Groove Radial Ball Bearing, Chrome Steel, 22mm x 56mm x 15mm, 157QMJ GY6-125/150, Honda style horizontal Crankshaft 90 - 110cc and other uses.

Bearing 6301 12mm x 37mm x 12mm Chrome Steel 139QMB 157QMJ CF250 172MM  B-1-1000-2025
$4.99 $4.99 Add to Cart

6301 Bearing, Open, Deep Groove Radial Ball Bearing, Chrome Steel, 12mm x 37mm x 12mm, GY6-50 139QMB, 157QMJ GY6-125/150 crankcase, CF250 172MM left crankcase (1), and others

Belt Cover Bolt Set Long Case 10 bolts GY6 150 157QMJ Scooter Moped ATV 200-1001-3002
$8.99 $8.99 Add to Cart

Belt Cover Bolts, Flanged Hex Bolts for  the GY6-125/150cc, 157QMJ, Long Case Belt Cover, (10 bolts)

Contains:

  • 8 - M6 x 1.00 x 40
  • 2 - M6 x 1.00 x 65
  • 1 - M6 x 1.00 x 12
Belt Cover Bolt Set Short Case 8 bolts GY6 150 157QMJ Scooter Moped ATV 200-1001-3003
$8.99 $8.99 Add to Cart

Belt Cover Bolts, Flanged Hex Bolts for the GY6-125/150cc, 157QMJ, Short Case Belt Cover, (8 bolts)

Contains:

  • 6 - M6 x 1.00 x 40
  • 2 - M6 x 1.00 x 65
  • 1 - M6 x 1.00 x 12
Belt Cover Chrome Racing Performance GY6 150 Long Case 10 bolt 157QMJ 201-1001-2010
$66.99 $66.99 Add to Cart

Belt Cover, Chrome, High Performance for the GY6-125/150 Long Case, left side transmission cover

Belt Cover Left CVT Cover Long Case 10 bolt GY6 150 157QMJ Scooter Moped ATV 200-1001-2006-B
$49.99 $49.99 Add to Cart

Belt Cover, Black, (Long Case), Left CVT Cover, GY6-125/150, QMI152/157 and QMJ152/157 engines. Overall length 19", fits Baja,  Boreem (BMS), Matrix 150, Roketa, SUNL, Tank, United Motors, Vento
Brake Cable Clamp GY6 139QMB 157QMJ B-200-1001-3104
$4.99 $4.99 Add to Cart

Clamp, Brake Cable, GY6-50, GY6-125/150 left side belt cover

Brake Light Switch Hydraulic GY6 50 150 250 Scooter Moped ATV B-1-1002-2001
$4.99 $4.99 Add to Cart

You have two brake switches on the GY6 139QMB, this is the larger type... found less often. (Measures approx. 12 1/2", 317mm)  They are found on the Bashan Classic, Dazon Sicilian, Lance Venice, Moto Fino MF50QT-2, Roketa Sicily MC-17, Schwinn Newport, Tank Viaggio, TNG Milano, Wanjie Big Chief, Zhen Lance Venice ZN150t-20 scooter and many others.

Mechanics Note: The brake switch on a scooter is not just to illuminate the brake light; it is also a safety switch to start the engine. If nothing happens when you push the start button, think about getting one or both of the brakes switches on your model.

Brake Light Switch Small End GY6 Honda Scooter Moped ATV B-1-1002-2002
$7.95 $7.95 Add to Cart

This is the smaller... most common brake switch found on the GY6 139QMB. (Measures approx. 11", 279mm) Brands and models include the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP, and many others.


Mechanics Note: The brake switch on a scooter is not just to illuminate the brake light; it is also a safety switch to start the engine. If nothing happens when you push the start button, think about getting one or both of these. Remember, you have two brake switches

Brake Switch with Spring Rear Foot Activated B-1-1002-2005
$9.99 $9.99 Add to Cart

Rear Brake Stop Switch and Spring for foot activated rear brake on many scooters and motorcycles.

Bulb Headlight B35 35w/35w FSL Scooter Moped ATV 1-1023-0003
$5.89 $5.89 Add to Cart

This 35w/35w headlight is a common bulb for many Handsome-boy scooters as well as ATVs. This 35w bulb is brighter and can often replace the 18w bulb. We also stock the 18w headlight if you prefer, as well.

  • BA20D
  • 35 Watt High Beam
  • 35 Watt Low Beam
  • 12 Volt
Bulb Headlight Halogen B35 35w/35w FSL Scooter Moped ATV 1-1023-0003-H
$5.89 $5.89 Add to Cart

This Halogen 35w/35w headlight is a common bulb for many Handsome-boy scooters as well as ATVs. This 35w bulb is brighter and can often replace the 18w bulb. We also stock the 18w headlight if you prefer, as well.

  • BA20D
  • 35 Watt High Beam
  • 35 Watt Low Beam
  • 12 Volt
Cam Chain Tensioner GY6 150 157QMJ Scooter Moped ATV 200-1004-6002
$10.49 $10.49 Add to Cart

This is the complete cam chain tensioner kit for the GY6 125cc and 150cc engines.

Camshaft GY6 150 157QMJ Scooter Moped ATV 200-1004-1006
$27.99 $27.99 Add to Cart

This is a good quality standard replacement camshaft assembly for the GY6 125cc and 150cc 152qmi and 157qmj engines. Performance cams are also available under our Performance Parts Section.

Carb Drain Tube Clamp GY6 50 150 139QMB 157QMJ B-200-1001-3103
$4.99 $4.99 Add to Cart

Clamp, Carb Drain Tube, GY6-50, GY6-125/150 left side belt cover

Carburetor 24mm (A) GY6 150 157QMJ Scooter Moped ATV 200-1005-1004-A
$62.99 $62.99 Add to Cart

This is a good quality Japanese made replacement carburetor with electric auto choke for the 4 stroke GY6 125/150cc 152QMI 152QMJ 157QMI 157QMJ engine. This carburetor fits most GY6 125/150cc engines on scooters, ATVs, quads, buggies and mopeds. This carburetor is found on Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

  • Intake (outer): 31mm
  • Intake (Inner): 24mm
  • Air Filter Mounting: 42mm
  • Choke: Auto Electric

     
Carburetor 24mm (C) GY6 150 157QMJ Scooter Moped ATV 200-1005-1004-C
$44.99 $44.99 Add to Cart

This is a lower quality less expensive replacement carburetor with electric auto choke for the 4 stroke GY6 125/150cc 152QMI 152QMJ 157QMI 157QMJ engine. This carburetor fits most GY6 125/150cc engines on scooters, ATVs, quads, buggies and mopeds. This carburetor is found on Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

  • Intake (outer): 31mm
  • Intake (Inner): 24mm
  • Air Filter Mounting: 42mm
  • Choke: Auto Electric

     
Carburetor Choke Enrichener NK200.05 Electric GY6 Scooter Moped ATV 1-1005-5001
$9.99 $9.99 Add to Cart

This is the carburetor choke enrichener for the GY6 50, 125, and 150cc Chinese 4-stroke engine. (139QMB, 157QMI, 157QMJ) It also fits many 2-stroke Chinese engines as well. It is an easy one screw installation. This choke is found on the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.  Referred to as NK200.05

Mechanics Note: This is usually the problem when the engine is difficult to start, won't stay running or runs fuel rich. This is an inexpensive and easy repair.

Carburetor Diaphragm GY6 150 157QMJ Scooter Moped ATV 200-1005-4002
$6.89 $6.89 Add to Cart
5 out of 5 Stars!

This is a new Carburetor Diaphragm (2 5/16", 58.5mm diameter, Piston Diameter 7/8", 21.9mm, Piston Length 1 1/2", 38mm) for the 4 stroke GY6 150 engines. A weak, torn or leaking diaphragm that will not allow you to get top performance or go to full speed. Ethenol fuel plays havok with our diaphragms.

Mechanics Note: If the engine is sluggish or won't allow you to run her up much past half on the throttle, and you are having difficulty getting her to full speed, look in the carburetor with the intake boot off, and see if the diaphragm is going all the way up. If it fails to do so, it is torn or leaking and you have found your problem.

Carburetor Main Jet  #115 Mikuni GY6 150 157QMJ B-200-1005-3005
$4.99 $4.99 Add to Cart

This is a carburetor main jet (M5 x .8, length 8mm) for the GY6 125cc and 150cc 152qmi and 157qmj engines. These are pretty easy to replace and a must if you want to upgrade your engine's performance with performance parts or upgrades.

Mechanics Note: If you increase the size of your stock carb jet you will want to improve your air flow both in and out of the engine.  For smaller upgrades replace the stock air filter with a Performance Air Filter for this engine.  If you upgrade beyond small adjustments you will want to install a Performance Exhaust to handle the increased combustion and minimize back flow issues.

Altitude can play an issue in scooter performance. When you are dealing with elevation you will want to rejet to prevent your engine from siezing and requiring a rebuild.  You will loose about 3% in power for every 1000' in elevation. At 4000' feet you will have lost about 12% of your power output.  You will want to go down one (1) jet size for every 1750' to 2000' you go up in elevation.  When the air is colder it requires bigger jets because cold air is more dense. If it is 50 degrees colder you would increase your jet size at least one step up.  If you don't your engine can sieze on you.

Carburetor Main Jet #125 Mikuni GY6 150 157QMJ B-200-1005-3006
$4.99 $4.99 Add to Cart

This is a carburetor main jet  (M5 x .8, length 8mm) for the GY6 125cc and 150cc 152qmi and 157qmj engines. These are pretty easy to replace and a must if you want to upgrade your engine's performance with performance parts or upgrades. This jet requires at least a Performance Air Filter.

Mechanics Note: If you increase the size of your stock carb jet you will want to improve your air flow both in and out of the engine. For smaller upgrades replace the stock air filter with a Performance Air Filter for this engine. If you upgrade beyond small adjustments you will want to install a Performance Exhaust to handle the increased combustion and minimize back flow issues.

Altitude can play an issue in scooter performance. When you are dealing with elevation you will want to rejet to prevent your engine from siezing and requiring a rebuild. You will loose about 3% in power for every 1000' in elevation. At 4000' feet you will have lost about 12% of your power output. You will want to go down one (1) jet size for every 1750' to 2000' you go up in elevation. When the air is colder it requires bigger jets because cold air is more dense. If it is 50 degrees colder you would increase your jet size at least one step up. If you don't your engine can sieze on you.

Carburetor Main Jet #135 Mikuni GY6 150 157QMJ B-200-1005-3007
$4.99 $4.99 Add to Cart

This is a carburetor main jet (M5 x .8, length 8mm) for the GY6 125cc and 150cc 152qmi and 157qmj engines. These are pretty easy to replace and a must if you want to upgrade your engine's performance with performance parts or upgrades. This jet requires and Performance Air Filter and a Performance Exhaust.

Mechanics Note: If you increase the size of your stock carb jet you will want to improve your air flow both in and out of the engine. For smaller upgrades replace the stock air filter with a Performance Air Filter for this engine. If you upgrade beyond small adjustments you will want to install a Performance Exhaust to handle the increased combustion and minimize back flow issues.

Altitude can play an issue in scooter performance. When you are dealing with elevation you will want to rejet to prevent your engine from siezing and requiring a rebuild. You will loose about 3% in power for every 1000' in elevation. At 4000' feet you will have lost about 12% of your power output. You will want to go down one (1) jet size for every 1750' to 2000' you go up in elevation. When the air is colder it requires bigger jets because cold air is more dense. If it is 50 degrees colder you would increase your jet size at least one step up. If you don't your engine can sieze on you.

Carburetor Rebuild Kit GY6 150 157QMJ Scooter Moped ATV 200-1005-2002
$13.99 $13.99 Add to Cart
5 out of 5 Stars!

This is a complete carburetor rebuild kit for the GY6, 4T, 125/150cc 152QMI 152QMJ 157QMI 157QMJ engine. The kit includes the main jet, pilot idle jet, air screw, spring, seal, seat, float, float valve, float pin, gasket, needle and clips. This kit fits carburetors in the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

CDI AC 6 Pin 4 Stroke GY6 1-1006-0011
$9.99 $9.99 Add to Cart

This is a 6-pin standard replacement AC fired CDI is for most GY6 Chinese engines. 139QMB, 157QMI, 157QMJ (This CDI has the 6-pin rounded receiver.) There is also a less common DC fired CDI availiable.  This CDI is found on the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others....

Mechanics Note: According to the experts, there is only one true way to know whether you have an AC or DC system. First, be sure your battery is fully charged and your fuse is good. Second, turn the key on, but DO NOT start your engine.  Using this CDI pin configuration:

[ 1 2 ][ 5 ]
[ 3 4 ][ 6 ]

with a voltage tester and leaving everything hooked up normal, go in through the top, through the wires until you have contact, check the #6 pin to see if it has 12v present?  Your system is DC  if you have 12V.  If not voltage then it is an AC system. Your AC system can have over 50v AC while cranking.

CDI AC 6 Pin Racing High Performance Non Rev GY6 50 150 139QMB 157QMJ 101-1006-0021
$12.99 $12.99 Add to Cart

This is an AC High Performance Racing CDI for the GY6 50cc, 125cc, and 150cc 139QMB, 152QMI and 157QMJ based engines. This CDI is similar to our orange performance CDI but has a more aggressive ignition advance curve. This is a performance CDI for the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.. We have the best quality ignition parts for Chinese engines!

Mechanics Note: According to the experts, there is only one true way to know whether you have an AC or DC system. First, be sure your battery is fully charged and your fuse is good. Second, turn the key on, but DO NOT start your engine.  Using this CDI pin configuration:

[ 1 2 ][ 5 ]
[ 3 4 ][ 6 ]

with a voltage tester and leaving everything hooked up normal, go in through the top, through the wires until you have contact, check the #6 pin to see if it has 12v present?  Your system is DC  if you have 12V.  If not voltage then it is an AC system. Your AC system can have over 50v AC while cranking.

CDI AC 6 pin Racing Non Rev GY6 Scooter Moped ATV 201-1006-0017
$9.89 $9.89 Add to Cart
5 out of 5 Stars!
  • This is a 6-pin AC Racing Performance CDI with an Unrestricted Rev Limit and an advanced timing curve for the GY6 50cc 125cc and 150cc engines. Engine applications include the 139QMB, 152QMI, 152QMJ, 157QMI, and 157QMJ.  These CDI's have no governor and eliminate that irritating rev-limiter which might be keeping your engine speed restricted
  • This CDI is found on the Baja, JMstar, Jonway, Lance, NST,Peace,Roketa, Sunl, Tank, TNG, Vento, VIP and many others. Compatibility, however, is based on matching wiring and connectors. Please ensure your make and model have the same connector and number of pins prior to ordering. This CDI has the rounded dual slot, 6-pin receiver and measures 2.5" x 1.5" x 1.5".
  • This high quality CDI is made tough and is durable on and off the track and will give your engine better acceleration and top end if your engine is in good running condition, including good compression. It is an inexpensive way to gain performance. Check our eBay store we have many different OEM and Racing Performance CDI's to choose from. We recommend taking a look at our high performance coils as well.

Mechanics Note: According to the experts, there is only one true way to know whether you have an AC or DC system. First, be sure your battery is fully charged and your fuse is good. Second, turn the key on, but DO NOT start your engine.  Using this CDI pin configuration:

[ 1 2 ][ 5 ]
[ 3 4 ][ 6 ]

with a voltage tester and leaving everything hooked up normal, go in through the top, through the wires until you have contact, check the #6 pin to see if it has 12v present?  Your system is DC  if you have 12V.  If not voltage then it is an AC system. Your AC system can have over 50v AC while cranking.

CDI DC 6 Pin Racing Non Rev GY6  50 -150 139QMB 157QMJ Scooter Moped ATV 201-1006-0012
$12.99 $12.99 Add to Cart
5 out of 5 Stars!
  • This is a 6-pin DC Racing Performance CDI with an Unrestricted Rev Limit and an advanced timing curve for the GY6 50cc 125cc and 150cc engines. Engine applications include the 139QMB, 139QMA  152QMI, 152QMJ, 157QMI, and 157QMJ.  These CDI's have no governor and eliminate that irritating rev-limiter which might be keeping your engine speed restricted. 
  • For this CDI your engine must have a 3-phase type generator and regulator/rectifier. This CDI has the rounded-style plug receiver. CDI Size: 3" x 1 5/8" x 15/16". 
  • This CDI is found on the Baja SC50 Sun City, Carter Brothers Interceptor GTR 250 with the SYM 250,  Diamo Velocity, Eton sport 50, JCL MP-150, Lance GSR 150, Schwinn, SYM sport 50, SYM VS125, Tomos Nitro 50, Vento Triton, VMOTO Monaco 125cc and other Korean, Chinese and Taiwanese scooters.and many others. Compatibility, however, is based on matching wiring and connectors. Please ensure your make and model have the same connector and number of pins prior to ordering.
  • Mechanics Note: According to the experts, there is only one true way to know whether you have an AC or DC system. First, be sure your battery is fully charged and your fuse is good. Second, turn the key on, but DO NOT start your engine.  Using this CDI pin configuration:

    [ 1 2 ][ 5 ]
    [ 3 4 ][ 6 ]

    with a voltage tester and leaving everything hooked up normal, go in through the top, through the wires until you have contact, check the #6 pin to see if it has 12v present?  Your system is DC  if you have 12V.  If not voltage then it is an AC system. Your AC system can have over 50v AC while cranking.


     

           

CDI DC High Performance Unlimited KYMCO Agility 50 125 KYMCO People 150 101-1006-0032
$28.99 $28.99 Add to Cart

This is a High Performance Non-Rev unlimited CDI for the KYMCO Agility 50cc and 125cc (2006-2011, 2012-2015 with this 6 pin 4 & 2 plug).  This CDI replaces KYMCO Part Number 30410-LBD6-E00.  This CDI is will also work on the KYMCO People 150 (2002-2011) , and KYMCO People 50 4 stroke (2006-2009) and KYMCO Sento 50 4 stroke (2009-2011).

Clutch Bell Chrome Racing GY6 150 157QMJ Scooter Moped ATV 201-1007-3004
$44.99 $44.99 Add to Cart

Clutch Bell, Chrome, Performance ventilated clutch bell, GY6-125/150 152QMI 157QMJ

Clutch Bell Housing Racing GY6 150 157QMJ Scooter Moped ATV 201-1007-3003
$44.99 $44.99 Add to Cart

This is a high quality heavy duty Performance Clutch Bell for the 4 stroke GY6 125cc 150cc 152QMI 152QMJ 157QMI 157QMJ scooter, moped, ATV & Go-Kart engines.

This Performance Clutch Bell housing fits a performance clutch.  It will often be too large for a OEM clutch.  We have the matching Performance Clutch part number 201-1007-0001 available for your convenience on our web site.

This better than original clutch bell, is built stronger to prevent warping, with better ventilation for proper cooling, and has better grab and power.

Measurements:

  • I/D: 125mm
  • O/D: 139mm
Clutch Nut (M12) CFmoto CF250 172MM F-1040-0012-FNSL1.25
$4.99 $4.99 Add to Cart

This is a Rear Clutch Nut for the CFmoto CF250 engine - scooter. (M12 x 1.50)

Clutch Nut (M12) GY6 150 157QMJ F-1040-0012-FNSL1.25
$4.99 $4.99 Add to Cart

This is a Rear Clutch Nut for the GY6-125cc 150cc 152QMI 152QMJ 157QMI 157QMJ scooter. (M12 x 1.25)

Clutch Racing GY6 150 157QMJ Scooter Moped ATV 201-1007-0001
$49.99 $49.99 Add to Cart

This is a High Performance Clutch for the GY6 125cc 150cc 152QMI 152QMJ 157QMI 157QMJ scooter, moped, ATV & go-kart engines. (Measures Approx. 4 3/4", 120mm on the backplate)

This performance clutch often requires a Performance Clutch Bell and may not fit your OEM bell. If it does not fit your OEM bell, we have the matching performance clutch bell housing part number  201-1007-3003

This clutch has high friction clutch pads with rigid backing plates!

Clutch Set 19 Spline GY6 150 157QMJ Scooter Moped ATV 200-1007-2003
$39.99 $39.99 Add to Cart

This is a completely assembled Clutch, Pulley and Bell Housing for the 19 spline 4 stroke GY6 125cc 150cc 152QMI 152QMJ 157QMI 157QMJ. This assembly includes the clutch, clutch springs, torque spring, pulley sheaves and bell housing. This is ready to install. This clutch fits Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

Measurements:

  • Bell I/D: 124.7mm (4 29/32")
  • Spline Count: 19
Clutch Springs 1K 1000 RPM Racing GY6 150 157QMJ Scooter Moped ATV 201-1029-2001
$7.89 $7.89 Add to Cart

These are 1000 RPM Performance Clutch Springs that fit all clutches on the Chinese GY6-125/150 4-stroke engines scooters, quads, mopeds, ATVs, go- karts, and buggies. These springs are available in 1K, 1.5K, and 2K spring rates. The GY6-125/150 Clutch Springs have an overall length of 35.9mm.  The coiled portion of the spring measures 14.9mm in length. Spring colors may vary.

Clutch Springs 2K 2000 RPM Racing GY6 150 157QMJ Scooter Moped ATV 201-1029-2003
$5.99 $5.99 Add to Cart

These are the 2000 RPM Performance Clutch Springs that fit all clutches on the Chinese GY6-125/150 4-stroke engines scooters, quads, mopeds, ATVs, go- karts, and buggies. These springs are available in 1K, 1.5K, and 2K spring rates. The GY6-125/150 Clutch Springs have an overall length of 35.9mm.  The coiled portion of the spring measures 14.9mm in length. Spring color may be red or chrome.

Clutch Torque Spring 1.5K 1500 RPM Racing GY6 150 157QMJ Scooter Moped ATV 201-1030-5002
$14.99 $14.99 Add to Cart
5 out of 5 Stars!

These are performance torque springs for the Chinese made GY6, 4T, 125/150cc engine 152QMI, 152QMJ, 157QMI, 157QMJ installed on scooters, quads, mopeds, ATVs, buggies and go-karts. These come in 1K, 1.5K, and 2K spring rates.  These are Performance Torque Springs to maximize your engine's torque and response. These top performing springs will give you back your acceleration, hill climbing ability and make your machine run as a top performer once again. Torque springs should be changed about every 800 miles because of heat and fatigue.

Mechanic Note: Torque Springs come in (3) different rates or RPM ratings, 1000 (1K) often Blue, 1500 (1.5K) often Yellow, and 2000 (2K) often RED. The lowest rated 1K may give you a higher speed overall but will engage at a lower RPM on take-off. If you or your scoot are heavy, you may be disappointed in the initial torque, take off and acceleration. The 1K will also have the hardest time "pulling the hills". On the other end the 2K will give you the greatest grabbing power and a higher RPM at take-off, and will pull the hills the best, but may be slower in speed overall. The 1.5K is in the middle. If you go with a heavier torque spring, you may want to go to a slightly higher variator roller or slider weight. At the same time, if you go to a lower RPM spring, you may need to go to a lighter weight. It is a fine line to find balance between torque spring and variator roller weight, achieved only through trial and error

Clutch Torque Spring 1K 1000 RPM Racing GY6 150 157QMJ Scooter Moped ATV 201-1030-5001
$14.99 $14.99 Add to Cart

These are performance torque springs for the Chinese made GY6, 4T, 125/150cc engine 152QMI, 152QMJ, 157QMI, 157QMJ installed on scooters, quads, mopeds, ATVs, buggies and go-karts. These come in 1K, 1.5K, and 2K spring rates.  These are Performance Torque Springs to maximize your engine's torque and response. These top performing springs will give you back your acceleration, hill climbing ability and make your machine run as a top performer once again. Torque springs should be changed about every 800 miles because of heat and fatigue.

Mechanic Note: Torque Springs come in (3) different rates or RPM ratings, 1000 (1K) often Blue, 1500 (1.5K) often Yellow, and 2000 (2K) often RED. The lowest rated 1K may give you a higher speed overall but will engage at a lower RPM on take-off. If you or your scoot are heavy, you may be disappointed in the initial torque, take off and acceleration. The 1K will also have the hardest time "pulling the hills". On the other end the 2K will give you the greatest grabbing power and a higher RPM at take-off, and will pull the hills the best, but may be slower in speed overall. The 1.5K is in the middle. If you go with a heavier torque spring, you may want to go to a slightly higher variator roller or slider weight. At the same time, if you go to a lower RPM spring, you may need to go to a lighter weight. It is a fine line to find balance between torque spring and variator roller weight, achieved only through trial and error 

Clutch Torque Spring 2K 2000 RPM Racing GY6 150 157QMJ Scooter Moped ATV 201-1030-5003
$14.99 $14.99 Add to Cart

These is the Racing Performance Torque Spring for the Chinese made GY6, 4T, 125/150cc engine 152QMI, 152QMJ, 157QMI, 157QMJ installed on scooters, quads, mopeds, ATVs, buggies and go-karts. 

 

   This Racing Performance Torque Spring maximizes your engine's torque and response. These top performing springs will give you back your acceleration, hill climbing ability and make your machine run as a top performer once again. Torque springs should be changed about every 800 miles because of heat and fatigue.


    Measurements:
I/D: 49.3mm
O/D: 58.4mm
Length: 151mm


    Mechanic Note: Torque Springs come in (3) different rates or RPM ratings, 1000 (1K) often Blue, 1500 (1.5K) often Yellow, and 2000 (2K) often RED all of which we sell in our eBay Store.

 

The lowest rated 1K may give you a higher speed overall but will engage at a lower RPM on take-off. If you or your scoot are heavy, you may be disappointed in the initial torque, take off and acceleration. The 1K will also have the hardest time "pulling the hills".  

 

    On the other end the 2K will give you the greatest grabbing power and a higher RPM at take-off, and will pull the hills the best, but may be slower in speed overall.

 

   The 1.5K is in the middle. If you go with a heavier torque spring, you may want to go to a slightly higher variator roller or slider weight. At the same time, if you go to a lower RPM spring, you may need to go to a lighter weight. It is a fine line to find balance between torque spring and variator roller weight, achieved only through trial and error Torque springs should be changed about every 800 miles because of heat and fatigue. 

Coil CFmoto 250cc 172MM CF250 CN250 Scooter ATV Quad Buggy Go Kart 600-1008-0010
$10.99 $10.99 Add to Cart

This is a standard OEM replacement Coil for the 4 Stroke, Chinese Engines, GY6 50, 150, 250, CH250, CN250, CF250, 139QMB, 157QMJ, 172MM

Coil High Performance GY6 CFmoto 250 Scooter Moped ATV 201-1008-0002
$12.39 $12.39 Add to Cart

This is a high performance ignition coil for all GY6, 4-stroke engines including the 50cc, 125cc, 150cc, and 250cc Chinese engine. This coil will greatly increase your spark and improve your performance, acceleration, starting, and fuel mileage. These are easy to install on any engine. This coil fits the 139QMB, 152QMI, 152QMJ, 157QMI, 157QMJ, CF250 and 172MM. This fits the GY6 on Baja, JMStar, Jonway, Lance, NST, Roketa, Sunl, Tank, Tomos, TNG, Vento, VIP and many others.
 
Mechanic Note : There is no guarantee of performance because engines may have other performance issues. Check out our rebuild kits to go to the next step!

Crankcase Cover Gasket Right GY6 150 157QMJ Scooter Moped ATV 200-1001-2106
$7.99 $7.99 Add to Cart

Crankcase Cover Gasket, Right, for 150cc and 125cc GY6 4-stroke QMI152/157 QMJ152/157 engines.

Crankcase Cover Plate Left GY6 150 157QMJ Scooter Moped ATV 200-1001-4005-P
$5.75 $5.75 Add to Cart

Crankcase Cover Plate, Left GY6-125/150cc, 4-stroke QMI152/157 and QMJ152/157 engines.








 
Crankcase Gasket Right GY6 150 157QMJ Scooter Moped ATV 200-1001-2105
$6.99 $6.99 Add to Cart

Crankcase Gasket, Right, for GY6-125/150, 4-stroke 152QMI 152QMJ 157QMI 157QMJ engines. 
Crankcase Left Long Case 10 bolt GY6 150 157QMJ 444mm 20" Scooter Moped ATV 200-1001-4004
$75.99 $75.99 Add to Cart

Crankcase, Left Side,  Long Case,  GY6-125/150cc GY6 4-stroke QMI152/157 QMJ152/157 engines. Overall Length 444mm,  20" long.
Crankcase O-Ring 7.5x1.5mm GY6 150 157QMJ B-200-1001-5003
$4.99 $4.99 Add to Cart

Crankcase O-Ring size 7.5*1.5 for 150cc and 125cc GY6 4-stroke QMI152/157 QMJ152/157 engines.

Crankcase Right GY6 150 157QMJ Scooter Moped ATV 200-1001-4005
$48.89 $48.89 Add to Cart

Crankcase, Right,  GY6-125/150cc 4-stroke QMI152/157 QMJ152/157 engines.

Crankshaft NPM Vitron Seal 19.8 x 30x5 GY6 139QMB 157QMJ Scooter Moped ATV 200-1009-0002
$5.99 $5.99 Add to Cart

This is a set of two NPM Vitron Crankshaft Seals, size 19.8x30x5 for the GY6-50 139QMB and GY6-125/150 152QMI 152QMJ 157QMI 157QMJ engines and many others.

Cylinder Bolt Nuts M8 x 1.25 Smooth Flanged Nut GY6 150 157QMJ F-1040-0008-FNS1.25
$4.99 $4.99 Add to Cart

M8 x 1.25, Smooth Flanged Nut, Cylinder Bolt Nuts for the GY6-125/150

Cylinder Dowel Pin (Pair) GY6 150 157QMJ B-200-1010-5002
$4.99 $4.99 Add to Cart

This is a complete replacement set of engine locator dowels (4) (O/D M10 x 16mm, I/D M8) for the 4 stroke GY6 125cc 150cc 152QMI 152QMJ 157QMI 157QMJ engine. Theses dowels go between the crankcase, cylinder and head.

Cylinder Head EGR 57.4mm Assembled GY6 150 157QMJ Scooter Moped ATV 200-1010-0005
$36.95 $36.95 Add to Cart
5 out of 5 Stars!

This is a complete standard EGR Cylinder head for the GY6 125cc 150cc 152QMI 152QMJ 157QMI 157QMJ engine. This includes the head and the entire valve set fully installed including the seals, seats, springs, and valves. This head fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50, Vento, VIP and many others..

Cylinder Head Non EGR 57.4mm Assembled GY6 150 157QMJ Scooter Moped ATV 200-1010-0006
$39.95 $39.95 Add to Cart

This is a complete 57.4mm Non-EGR replacement Cylinder Head for the GY6-125/150cc 152QMI 152QMJ 157QMI 157QMJ engine.  This includes the head with fully installed seals, seats, springs, studs and moly coated valves.  The head bolts measure 54mm center to center, square. This head fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Tomos Nitro 50, Vento, VIP and many others..

Cylinder Long Stud Bolts (Pair) 196mm M8x1.25 GY6 150 157QMJ B-200-1010-4004
$4.99 $4.99 Add to Cart

Cylinder Long Stud Bolts, 1 Pair, 196mm, M8x1.25, thread length 20mm & 16mm, Crankcase Bolts, GY6-125/150, Quality, long studs for cinching down the entire top end.

Cylinder Short Stud Bolts (Pair) 188mm M8x1.25 GY6 150 157QMJ B-200-1010-4003
$4.99 $4.99 Add to Cart

Cylinder Short Stud Bolts, 1 Pair, 188mm, M8x1.25, thread length 19mm & 17mm, Crankcase Bolts, GY6-125/150, Quality, short studs for cinching down the entire top end.

Cylinder Top End Rebuild Kit GY6 150 157QMJ Scooter Moped ATV 200-1010-3002
$58.95 $58.95 Add to Cart

This is the standard Top End Rebuild Kit for the 4 stroke GY6-125/150 152QMI 152QMJ 157QMI 157QMJ engine.  This kit includes the cylinder, a moly coated piston, all the rings, wrist pin and gaskets. This kit will also bring your 125cc to a 150cc.

Exhaust Gasket Ring GY6 150 157QMJ B-200-1013-2001
$4.99 $4.99 Add to Cart

This is a Exhaust Gasket Ring for the 4 stroke GY6 125cc 150cc 152QMI 152QMJ 157QMI 157QMJ engine. Make your engine sound good again. This gasket fits Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

Exhaust Stud (6M x 1.0) Muffler Cap Nut GY6 Honda Style Horizontal Dirt Pit Bike Quad ATV F-1040-0006-CAPN1.0
$4.99 $4.99 Add to Cart

Exhaust Stud (6M x 1.0) and Muffler Cap Nut for the 6mm GY6 50cc, 125cc, 150cc, Horizontal 50 -125

Exhaust Stud Bolt Set 6mm (Set of 2) GY6 50 150 139QMB 157QMJ B-100-1013-3000
$4.99 $4.99 Add to Cart

This is a replacement exhaust stud bolt set (M6 x 1.0 x 32mm)is for the 4-stroke, GY6 50cc and some 125cc and 150cc engines. These directly replace the stock bolts.

Exhaust Stud Bolt Set 8mm (Pair) GY6 150 157QMJ B-200-1013-3001
$4.99 $4.99 Add to Cart

Exhaust Stud Bolts, (1 Pair) M8x1.25 for the 172MM 250cc 4-stroke water-cooled CF250 CN250 engines and GY6 125cc/ 150cc  and the ZNEN GY6 150cc 4-stroke engines found on the Bintelli, Gorilla Motor Works (GMW) and Puma scooters and many others makes & models.

Exhaust Stud Nuts (Pair) GY6 6M Locking Alloy F-1040-0006-CN1.00
$4.99 $4.99 Add to Cart

This is one pair (2) nut fasteners for the GY6 Exhaust Stud Bolts.  This is made from a special aircraft alloy metal that withstands high temperatures.  This is a locking nut to handle the vibrations.  Also, this nut will not rust or corrode, making it much easier to change or remove at some later date.

Flywheel Rotor Magneto 11-Pole GY6 150 157QMJ Scooter Moped ATV 200-1032-2005
$20.29 $20.29 Add to Cart

Flywheel, Rotor, Magneto, (11-Pole),  GY6-125/150, Quality

Flywheel Rotor Nut (M12) GY6 150 157QMJ F-1040-0012-FNSL1.25
$4.99 $4.99 Add to Cart

This is a replacement Flywheel Rotor Nut to replace your stripped out, worn out or lost original. (M12 x 1.25)

Fuel Filter In line Universal B-1-1016-0001
$4.99 $4.99 Add to Cart

This is a standard universal in-line fuel filter for your scooters, buggies, quads, ATVs, go-karts, dirt bikes and pit bikes.

Fuel Pump Vacuum operated GY6 139QMB 157QMJ 1-1016-1007
$24.99 $24.99 Add to Cart

Fuel Pump, GY6-50 - 150cc, 4-stroke, Vacuum operated,  Hole spacing: 76mm,  Overall Height: 33.5mm, fits various makes and model scooters

Fuel Valve 3 way In line GY6 Scooter Moped ATV 1-1016-1001
$11.99 $11.99 Add to Cart

This is an easy to install, single bolt mount, 3-way, 3-port in-line vacuum operated fuel valve petcock (aka fuel pump) for many engines including the GY6 engine. This valve can be found on the Adly, Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP, and many others... We ship the same day as ordered, for quick service!

Mechanics Note: If the diaphragm inside this valve fails, it will supersede your carburetor float valve and cause your engine to flood to where it will cause it to lock-up while sitting. This valve has a single bolt mount for easy installation. . Get quality products you can trust from us!

Fuel Valve 4 Way In Line GY6 139QMB 157QMJ 1-1016-1004
$11.99 $11.99 Add to Cart

Fuel Valve Petcock, 4-Way, 4-Port, (In-Line), GY6, 4-stroke, vacuum operated, Hole I/D: 7mm, (fits Tank, Sunl, Roketa, Vento, TNG, VIP, Baja, Jonway, JMstar, Peace, Lance, NST, Adly as well as others)

Fuel Valve M14 x1.0 Eton E-ton Beamer I Eton Beamer II Scooters 750128 1-1016-1005
$17.89 $17.89 Add to Cart
5 out of 5 Stars!

This vacuum operated, tank-mounted, fuel valve petcock (aka fuel pump) is found on the 2005 & earlier and 2006 - 2010 E-TON Beamer PN, PN2, PN2B, PN2C, PN2D, and PN2G, with OEM part numbers 750128 .  This valve has been known to fit some Benelli, Diamo, Eurastrada Rx8 50cc 2T, Honda's, Honda Aero 83 - 84, Honda Spree 83 -84,  Keeway, Matrix 50, some QJ scooters such as QJ B08, Strada RX8, Velocity GTX 50, Vento Phantom R4I and Vento Triton, Yamati,.  These valves often go bad or are suspect.

Please check your measurements before ordering since we sell 3 different fuel valves which look exactly alike with the only difference being the internal measurements. All 3 valves have a 22mm nut.

Please note that Eton uses two different fuel valves. Some Eton products such as the Viper, Yukon and Yukon II take our other listing, the M16x1.0 Fuel Valve,   Please measure the nipple on the bottom of your tank or the inside diameter of the valve nut to see if it is M14 (.55", just under 9/16") or 16mm (.62" 5/8")  to be sure you are ordering the correct one for your engine.  Both Valves have a wrench size of 22mm to remove the nut and valve.
 

Measurements:

  • Valve Nut I/D: 14mm
  • Tank Nipple O/D: 13.99mm
  • Nipple Threads; Very- Fine
  • Nut Wrench Size: 22mm

 

 


 

Fuel Valve M16x1.0 Eton E-ton Viper Yukon Yukon II Scooter Moped ATV 810419 1-1016-1006
$15.99 $15.99 Add to Cart
4 out of 5 Stars!

This vacuum operated, tank-mounted, fuel valve petcock (aka fuel pump) is found on many of the E-TON buggies, scooters & ATV's with OEM part numbers 810419 These valves often go bad or are suspect.

These fit the E-TON 2009 Viper 150 RXL-150R09, 2005 - 2008 Viper 150 RXL-150R, Yukon 155cc, 2008 & earlier Yukon YXL-150, 2005 - 2010 Yukon II CXL-150 and many other brands and models.

Please note that Eton uses two different valves. Most Eton Beamers take the M14x1.0 Fuel Valve.  Please measure the nipple on the bottom of your tank or the inside diameter of the valve nut to see if it is M14 (.55", just under 9/16") or 16mm (.62" 5/8")  to be sure you are ordering the correct one for your engine.  Both Valves have a wrench size of 22mm to remove the nut and valve.
 

Fuel Valve M16X1.5 GY6 139QMB 157QMJ 172MM Scooter Moped ATV 1-1016-1002
$9.99 $9.99 Add to Cart

This is the most commonly found tank mounted Fuel Valve Petcock, (M16x1.5), GY6-50, GY6-125, GY6-150, GY6-250, 139QMB, 152QMI, 152QMJ, 157QMI, 157QMJ, 172MM, vacuum operated, fits Baja, Jonway, JMstar, Peace, Lance, NST,  Roketa, Sunl, Tank, TNG, Vento, VIP, as well as others.

Measurements:

  • Valve Nut I/D: 16mm +
  • Tank Nipple O/D: 15.75mm
  • Nipple Threads; Semi- Fine
  • Nut Wrench Size: 22mm
Fuse GY6 Scooter Moped Quad ATV Go Karts B-1-1049-0003
$4.99 $4.99 Add to Cart

This is the standard replacement barrel fuse for all GY6 scooters, ATVs, quads and buggies. It is good to have extras when you need them.

Gasket Head & Base Set 52mm GY6 125 152QMI 152QMJ Scooter Moped ATV 200-1017-1024
$5.99 $5.99 Add to Cart

This is a Complete Head and Base Gasket Set for the 4 Stroke, 52mm GY6-125, 152QMI 152QMJ engine. This complete gasket set fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

Gasket Head & Base Set 57.4mm GY6 150 157QMI 157QMJ Scooter Moped ATV 200-1017-1025
$5.99 $5.99 Add to Cart

This is a Complete Head and Base Gasket Set for the 4 Stroke, 57.4mm, GY6-150, 157QMI 157QMJ engine. This complete gasket set fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.

Gasket Head & Base Set 59mm GY6 155 Big Bore 157QMJ Scooter Moped ATV 201-1017-0015
$7.89 $7.89 Add to Cart

This is the Head and Base Gasket Set for the 59mm GY6-155 Big Bore Kit.

Gasket Intake Manifold Insulator GY6 150 157QMJ B-400-1005-2010
$4.99 $4.99 Add to Cart

This is the Intake Manifold Insulator Gasket for the 4 stroke GY6 125 150cc 152QMI 152QMJ 157QMI 157QMJ engine.

Mechanics Note: This gasket sits between the head and the manifold. Like the manifold, these will get old over time and leak air causing the engine to run poorly. We suggest you replace these and the Insulator whenever you change the manifold to avoid problems later. Keep these in stock!

Gasket Set 52mm GY6 125 Long Case 152QMI 152QMJ Scooter Moped ATV 200-1017-0017
$9.89 $9.89 Add to Cart

This is a Complete Gasket Set for the Long Case (10 bolts on the Belt Cover) GY6-125 125cc 52mm engine. This has all your gaskets in one easy package. This complete gasket set fits the Baja, JMstar, Jonway, Lance, NST, Peace, Roketa, Sunl, Tank, TNG, Vento, VIP and many others.